hascopy.blogg.se - Giga nas dongle firmware

#Giga nas dongle firmware drivers
#Giga nas dongle firmware windows 10
#Giga nas dongle firmware mac

Sabrent USB 3.0 to 2.5GbE Adapter NIC to Switch 10 feet / 3.05 meters: 1.3W.

Sabrent USB 3.0 to 2.5GbE Adapter NIC 300 feet / 91.44 meters: 1.8W.

We measured the impact on an Intel Atom C3558 server because that platform has relatively stable clock speeds and a low platform power base so we could see the impact measured at the wall. We also tested the solution on a short connection to the switch using CAT6. We tested the NIC both in a direct attach 2.5Gbps connection using CAT5e near the edge of the 100-meter maximum run length. We could not find power consumption ranges listed for its NIC. Sabrent USB 3.0 to 2.5GbE Adapter NIC Power Consumption Users will likely experience worse performance if they put this NIC on a busy USB 3.0 hub. We will also note that we are using this directly connected to the motherboard, not using an external hub. That is unsurprising since this adapter uses the same chip as those two. It is also effectively tied with the CableCreation and Plugable units. Overall, we saw similar results when used in USB Type-A and Type-C ports. We also used the speed setting to manually drop speeds from 2.5GbE to 1GbE. We also pushed these through a multi-gigabit switch and saw the same results within a 0.7% margin of error on both setups.

#Giga nas dongle firmware windows 10

We tested the unit directly attached between two Windows 10 PCs going from the Sabrent USB 3.0 Type-A to 2.5GbE NIC to a TEG-25GECTX NIC. There are a number of features such as VLAN tagging and Jumbo Frames that one may want to change after setting up the NIC in the standard network adapter configuration, but everything was where we expected. We also tested at 1GbE speeds as well: Sabrent USB To 2.5GbE NIC In Windows 1GbE Status Sabrent USB To 2.5GbE NIC In Windows 2.5GbE Status You can see that the card immediately connected to our multi-gig switch and negotiated at 2.5Gbps speeds.

#Giga nas dongle firmware mac

OSX is also supported although we did not get to test on the Mac Mini M1 due to timing of this review. You just need Kernel 5.x and support is built-in. We are showing Windows 10 here but Ubuntu 20.04 LTS works out of the box as well.

#Giga nas dongle firmware drivers

There are updated drivers on Realtek’s website compared to what is now shipping with Windows 10, and modern Linux distros, but having easy plug-and-play functionality is nice. Sabrent USB To 2.5GbE NIC In Windows With Realtek USB 2.5GbE Family Adapter Realtek makes variants of their adapters with built-in interface differentiation so one does not need a PCIe to USB bridge chip. In our Syba 2.5 Gigabit Ethernet PCIe NIC Review, we saw the RTL8125 which is the 2.5GbE to PCIe version.

You can see here that it identifies as a “Realtek USB 2.5GbE” adapter because the Realtek RTL8156 chipset is the company’s 2.5GbE to USB single-chip solution. It identifies as a Realtek 2.5GbE NIC and everything works. You plug in the adapter, and it connects with a DHCP address. In Windows 10, the Sabrent 2.5GbE adapter was dead simple to set up. This port also works at 100Mbit and 1GbE modes as well while supporting 802.3bz for 2.5GbE. You can plug a standard wired Ethernet cable in and this will work. The networking side is a 2.5GbE capable RJ45 port. Sabrent USB 3 To 2.5GbE USB Type C Adapter And RJ45 The metal also helps with heat dissipation so it is functional as well. This is not a cheap plastic case which we really like. Of the three, the Sabrent chassis is the heaviest, but that is because it is made of metal. Sabrent USB 3 To 2.5GbE Connectedįar and away the one item that stands apart on the Sabrent unit is the chassis. We like the option to run USB Type-C, but with Project TinyMiniMicro nodes, as an example, we will use Type-A ports for a 2.5GbE adapter. This is a Gen1 USB 3 device so the port speed is only 5Gbps which is fine for a 2.5GbE NIC. While we like the option to run Type-C, if there is a Type-A port available we generally think it is advisable to run in the Type-A port. This is between the Plugable (USB Type-C standard with a Type-A converter on a lanyard) and the CableCreation unit that is Type-A only. What is unique here is that there is a Type-A to Type-C converter included. On one side of the adapter, there is a USB Type-A port. Sabrent USB-C and USB Type-A to 2.5GbE Ethernet Adapter Hardware Overview In terms of the pricing, the Sabrent model is about $5 more than the CableCreation and $5 less than the Plugable so we wanted to see if it provides a middle ground in our review. A few months ago we reviewed the CableCreation USB 3 Type-A 2.5GbE Adapter and then the Plugable 2.5GbE USB-C and USB to Ethernet Adapter. Since we have reviewed two other popular USB 3.0 to 2.5GbE adapters this year, we figured we would review the third one we see commonly used, the Sabrent 2.5GbE USB network adapter or NT-S25G.